Dsxpnm Serial Interface
I have a cisco 7206 VXR with a DS3 card PA-T3+ (From Mpls) to a cisco 3845 with a card NM-1te/E3 port adapter.
3845(config)#card type t3 1/0
3845(config)#contr t3 1
3845(config-con)#frammin c-bit
3845(config-con)#clock source internal
3845(config-if)#idsu mode 0
3845(config-if)#dsu bandwidth
attached are some information from my 3845 router
3845#sh contr t3 1/0 brief
T3 1/0 is down.
Applique type is Subrate T3
Transmitter is sending remote alarm.
Receiver has no alarms.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Internal
3845#sh int s1/0
Serial1/0 is down, line protocol is down
Hardware is DSXPNM Serial
Description: DS3 to Mpls- X0-mn-HFGS/541589/TWQ//-LEC-94/HFGS/202473//03
Internet address is 10.252.1.22/30
MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of 'show interface' counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 3374 interface resets
0 output buffer failures, 0 output buffers swapped out
3 carrier transitions
DSU mode 0, bandwidth 44210, real bandwidth 44210, scramble 0
3845#sh contr s1/0
Interface Serial1/0
Hardware is DSXPNM GT96K
idb at 0x6470C9B4, driver data structure at 0x6470DCA8
GT96K Port Used 2, SCC Num 2
MPSC Registers:
MMCR_L=0x001B04C0, MMCR_H=0x40000000, MPCR=0x00000000
CHR1=0x00FE007E, CHR2=0x00000000, CHR3=0x000011E8, CHR4=0x00000000
CHR5=0x00000000, CHR6=0x00000000, CHR7=0x00000000, CHR8=0x00000000
CHR9=0x00000000, CHR10=0x00001008, CHR11=0x0083F83E
SDMA Registers:
SDC=0x00003301, SDCM=0x00000000, SGC=0x00000000
CRDP=0x2E562220, CTDP=0x2E562660, FTDB=0x2E562660
BRG Conf Register=0x00480000
Rx Clk Routing Register=0x00000800 Tx Clk Routing Register=0x00000900
Main Routing Register (MRR) addr=0x4B701A00, val=0x00FFFE3F
GPP Registers:
Conf =0x0000007F, Io =0x00000006, Data =0x7E7E7E46, Level =0x00000000
Conf0=0x0 , Io0=0x0 , Data0=0x7E7EFFFF, Level0=0x0
SUBRATE FPGA Registers (Clear T3/E3):
On my 7206VXR -----------------It's on the serial 5/0
***** The link is down, I am not able to have it up *******************************
72061#sh contr s5/0
M1T-T3+ pa: show controller:
PAS unit 29, subunit 0, f/w version 3-93, rev ID 0x2800001, version 3
idb = 0x65646F20, ds = 0x6567CA1C, ssb=0x646CBB6C
Clock mux=0x30, ucmd_ctrl=0x0, port_status=0x0
Serial config=0x8, line config=0x1B0202
maxdgram=4584, bufpool=128Kb, 256 particles
rxLOS inactive, rxLOF inactive, rxAIS inactive
txAIS inactive, rxRAI active, txRAI inactive
line state: down
cable type : T3 cable, received clockrate 44202795
base0 registers=0x3E800000, base1 registers=0x3E802000
mxt_ds=0x65629B80, rx ring entries=124, tx ring entries=254
statring=0xE3AF5A0, statr shadow=0x656289C0, stat_head=117
rxring=0xE3C79C0, rxr shadow=0x6576AE88, rx_head=117
txring=0xE3C5EE0, txr shadow=0x655EAB50, tx_head=0, tx_tail=0, tx_count=0
throttled=0, enabled=0
halted=0, last halt reason=0
Microcode fatal errors=0
rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0
rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0x2C
tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(256)
tx_fullring=0, tx_started=69, mxt_flush_count=0
rx_int_count=59108, tx_int_count=69
Framing is c-bit, Clock Source is Line
Bandwidth limit is 44210, DSU mode 0, Cable length is 25
rx FEBE since last clear counter 2137100962, since reset 0
Data in current interval (724 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 724 Unavailable Secs
0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs
Data in Interval 1:
7206#sh int s5/0
Serial5/0 is down, line protocol is down
Hardware is M1T-T3+ pa
Description: DS3 to Columbus- X0-mn/HFGS/541589/tqw//
Internet address is 10.252.1.21/30
MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec,
reliability 251/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Restart-Delay is 0 secs
Last input 18:25:51, output 18:25:46, output hang never
Last clearing of 'show interface' counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
65 packets input, 4712 bytes, 0 no buffer
Received 16 broadcasts, 0 runts, 2 giants, 0 throttles
0 parity
261 input errors, 257 CRC, 0 frame, 1 overrun, 0 ignored, 1 abort
69 packets output, 5226 bytes, 0 underruns
0 output errors, 0 applique, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
6 carrier transitions
rxLOS inactive, rxLOF inactive, rxAIS inactive
txAIS inactive, rxRAI active, txRAI inactive
txAIS inactive, rxRAI active, txRAI inactive
7206#sh run
Building configuration..
Current configuration : 9834 bytes
!
! Last configuration change at 05:30:03 CST Tue Mar 11 2008
! NVRAM config last updated at 09:15:32 CST Wed Feb 27 2008
!
version 12.4
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname MPLS-RT1
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$2j0m$nC2PPntRlhnkUzb9ZBdAP0
!
no aaa new-model
clock timezone CST -6
clock summer-time est recurring 1 Sun Apr 0:01 last Sun Oct 0:01
clock calendar-valid
!
!
ip cef
no ip domain lookup
ip domain name cbca.com
!
!
ipx routing 001b.2be0.481b
!
!
!
!
!
!
!
!
!
!
!
!
!
!
controller T1 2/0
framing esf
linecode b8zs
channel-group 0 timeslots 1-4
!
controller T1 2/1
framing esf
linecode b8zs
channel-group 0 timeslots 1-24
!
!
t1 1 channel-group 0 timeslots 1-24
t1 2 channel-group 0 timeslots 1-24
t1 3 channel-group 0 timeslots 1-24
t1 4 channel-group 0 timeslots 1-24
description T3 Point-to-Multipoint
!
source-bridge ring-group 9
dlsw local-peer peer-id 10.12.1.1
dlsw remote-peer 0 tcp 10.92.1.1
!
!
interface Loopback0
ip address 10.12.1.1 255.255.0.0
!
interface Tunnel1
no ip address
!
interface TokenRing3/2
no ip address
shutdown
ring-speed 16
!
interface TokenRing3/3
no ip address
shutdown
ring-speed 16
!
interface Serial5/0
description DS3 to Columbus- X0-mn/HFGS/541589/tqw//
ip address 10.252.1.21 255.255.255.252
dsu bandwidth 44210
framing c-bit
cablelength 25
serial restart-delay 0
!
interface Serial6/0/1:0
no ip address
!
interface Serial6/0/2:0
description T1 to Dallas - X0-MN/HCGZ/043567TQW LEC-MN-HCGS-043567
ip address 10.252.1.57 255.255.255.252
no ip route-cache cef
no ip route-cache
fair-queue 64 16 0
!
interface Serial6/0/3:0
no ip address
*******************************************************************************************
Initialy, I was receiving AIS from my remote site (3845), then I have somebody to flip the coax cable at my remotr site, then the AIS inicator went away but the FERF indicator came on.
Well! well !, i need help
Errors on T3 Interfaces. We just switched over to a frac T3. Drag racing apk mod download. Hardware is DSXPNM Serial Internet address is y.y.y.162/30 MTU 4470 bytes, BW 12631 Kbit. Download lagu soundtrack love in paris season 2. Sambomaster wa kimi ni katarikakeru rar.
On the 3845 , I have the folowing code on the card :3845(config)#card type t3 1/0
3845(config)#contr t3 1
3845(config-con)#frammin c-bit
3845(config-con)#clock source internal
3845(config-if)#idsu mode 0
3845(config-if)#dsu bandwidth
attached are some information from my 3845 router
3845#sh contr t3 1/0 brief
T3 1/0 is down.
Applique type is Subrate T3
Transmitter is sending remote alarm.
Receiver has no alarms.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Internal
3845#sh int s1/0
Serial1/0 is down, line protocol is down
Hardware is DSXPNM Serial
Description: DS3 to Mpls- X0-mn-HFGS/541589/TWQ//-LEC-94/HFGS/202473//03
Internet address is 10.252.1.22/30
MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of 'show interface' counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 3374 interface resets
0 output buffer failures, 0 output buffers swapped out
3 carrier transitions
DSU mode 0, bandwidth 44210, real bandwidth 44210, scramble 0
3845#sh contr s1/0
Interface Serial1/0
Hardware is DSXPNM GT96K
idb at 0x6470C9B4, driver data structure at 0x6470DCA8
GT96K Port Used 2, SCC Num 2
MPSC Registers:
MMCR_L=0x001B04C0, MMCR_H=0x40000000, MPCR=0x00000000
CHR1=0x00FE007E, CHR2=0x00000000, CHR3=0x000011E8, CHR4=0x00000000
CHR5=0x00000000, CHR6=0x00000000, CHR7=0x00000000, CHR8=0x00000000
CHR9=0x00000000, CHR10=0x00001008, CHR11=0x0083F83E
SDMA Registers:
SDC=0x00003301, SDCM=0x00000000, SGC=0x00000000
CRDP=0x2E562220, CTDP=0x2E562660, FTDB=0x2E562660
BRG Conf Register=0x00480000
Rx Clk Routing Register=0x00000800 Tx Clk Routing Register=0x00000900
Main Routing Register (MRR) addr=0x4B701A00, val=0x00FFFE3F
GPP Registers:
Conf =0x0000007F, Io =0x00000006, Data =0x7E7E7E46, Level =0x00000000
Conf0=0x0 , Io0=0x0 , Data0=0x7E7EFFFF, Level0=0x0
SUBRATE FPGA Registers (Clear T3/E3):
On my 7206VXR -----------------It's on the serial 5/0
***** The link is down, I am not able to have it up *******************************
72061#sh contr s5/0
M1T-T3+ pa: show controller:
PAS unit 29, subunit 0, f/w version 3-93, rev ID 0x2800001, version 3
idb = 0x65646F20, ds = 0x6567CA1C, ssb=0x646CBB6C
Clock mux=0x30, ucmd_ctrl=0x0, port_status=0x0
Serial config=0x8, line config=0x1B0202
maxdgram=4584, bufpool=128Kb, 256 particles
rxLOS inactive, rxLOF inactive, rxAIS inactive
txAIS inactive, rxRAI active, txRAI inactive
line state: down
cable type : T3 cable, received clockrate 44202795
base0 registers=0x3E800000, base1 registers=0x3E802000
mxt_ds=0x65629B80, rx ring entries=124, tx ring entries=254
statring=0xE3AF5A0, statr shadow=0x656289C0, stat_head=117
rxring=0xE3C79C0, rxr shadow=0x6576AE88, rx_head=117
txring=0xE3C5EE0, txr shadow=0x655EAB50, tx_head=0, tx_tail=0, tx_count=0
throttled=0, enabled=0
halted=0, last halt reason=0
Microcode fatal errors=0
rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0
rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0x2C
tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(256)
tx_fullring=0, tx_started=69, mxt_flush_count=0
rx_int_count=59108, tx_int_count=69
Framing is c-bit, Clock Source is Line
Bandwidth limit is 44210, DSU mode 0, Cable length is 25
rx FEBE since last clear counter 2137100962, since reset 0
Data in current interval (724 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 724 Unavailable Secs
0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs
Data in Interval 1:
7206#sh int s5/0
Serial5/0 is down, line protocol is down
Hardware is M1T-T3+ pa
Description: DS3 to Columbus- X0-mn/HFGS/541589/tqw//
Internet address is 10.252.1.21/30
MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec,
reliability 251/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Restart-Delay is 0 secs
Last input 18:25:51, output 18:25:46, output hang never
Last clearing of 'show interface' counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
65 packets input, 4712 bytes, 0 no buffer
Received 16 broadcasts, 0 runts, 2 giants, 0 throttles
0 parity
261 input errors, 257 CRC, 0 frame, 1 overrun, 0 ignored, 1 abort
69 packets output, 5226 bytes, 0 underruns
0 output errors, 0 applique, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
6 carrier transitions
rxLOS inactive, rxLOF inactive, rxAIS inactive
txAIS inactive, rxRAI active, txRAI inactive
txAIS inactive, rxRAI active, txRAI inactive
7206#sh run
Building configuration..
Current configuration : 9834 bytes
!
! Last configuration change at 05:30:03 CST Tue Mar 11 2008
! NVRAM config last updated at 09:15:32 CST Wed Feb 27 2008
!
version 12.4
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname MPLS-RT1
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$2j0m$nC2PPntRlhnkUzb9ZBdAP0
!
no aaa new-model
clock timezone CST -6
clock summer-time est recurring 1 Sun Apr 0:01 last Sun Oct 0:01
clock calendar-valid
!
!
ip cef
no ip domain lookup
ip domain name cbca.com
!
!
ipx routing 001b.2be0.481b
!
!
!
!
!
!
!
!
!
!
!
!
!
!
controller T1 2/0
framing esf
linecode b8zs
channel-group 0 timeslots 1-4
!
controller T1 2/1
framing esf
linecode b8zs
channel-group 0 timeslots 1-24
!
!
Com Port Settings Windows 10
controller T3 6/0t1 1 channel-group 0 timeslots 1-24
t1 2 channel-group 0 timeslots 1-24
t1 3 channel-group 0 timeslots 1-24
t1 4 channel-group 0 timeslots 1-24
description T3 Point-to-Multipoint
!
source-bridge ring-group 9
dlsw local-peer peer-id 10.12.1.1
dlsw remote-peer 0 tcp 10.92.1.1
!
!
interface Loopback0
ip address 10.12.1.1 255.255.0.0
!
interface Tunnel1
no ip address
!
interface TokenRing3/2
no ip address
shutdown
ring-speed 16
!
interface TokenRing3/3
no ip address
shutdown
ring-speed 16
!
interface Serial5/0
description DS3 to Columbus- X0-mn/HFGS/541589/tqw//
ip address 10.252.1.21 255.255.255.252
dsu bandwidth 44210
framing c-bit
cablelength 25
serial restart-delay 0
!
interface Serial6/0/1:0
no ip address
!
interface Serial6/0/2:0
description T1 to Dallas - X0-MN/HCGZ/043567TQW LEC-MN-HCGS-043567
ip address 10.252.1.57 255.255.255.252
no ip route-cache cef
no ip route-cache
fair-queue 64 16 0
!
interface Serial6/0/3:0
no ip address
*******************************************************************************************
Initialy, I was receiving AIS from my remote site (3845), then I have somebody to flip the coax cable at my remotr site, then the AIS inicator went away but the FERF indicator came on.
Well! well !, i need help